Haier Washer and Dryer Error Codes – Problems and Meaning
Haier washers error codes are a crucial source of information for users. These codes help users monitor their machines’ performance and diagnose issues. Error codes enable users to understand and potentially resolve problems with their devices before seeking technical support. They empower users to troubleshoot efficiently and use their Haier washing machines effectively. Haier washing machine error codes serve as an essential resource for users seeking to maximize the utility of their appliances.
Codes List
| Error Codes | Solutions |
|---|---|
| Err1 | Door is not properly shut. Shut the door properly |
| Err2 | Drainage error, water not emptied within 6 minutes. Clean the filter and check the drain hose for blockage. If error still exists, please contact the maintenance personnel |
| Err3 | Temperature sensor not properly connected or damaged. Contact the maintenance personnel. |
| Err4 | Heater error (Appears at the end of a cycle). Reduce load and then start washing again. If problem still exists, please contact the maintenance personnel |
| Err5 | Water level not met in 8 minutes. The height of the drain hose is below 80 cm. The drain hose is in water. Make sure that tap is turned on, and water pressure is normal. If problem still exists, please contact the maintenance personnel. Install drain hose within 80-100 cm of height. Make sure the drain hose is not in water. |
| Err6 | Motor error |
| Err7 | Motor error |
| Err8 | Water exceeds protective level. |
| End | End of wash cycle . |
| 1:25 | The remaining time is 1 hour 25 minutes |
| 19:25 | Status information:Preset time for delayed operation. |
| UNb | After the last rinsing cycle finishes,spinning fails completely due to unbalance of the laundry |
| do | Washer lid is Open. The washer has detectedthat the lid is open. The washer will not start with thewasher lid open. If the lid is openedduring the wash cycle, it maycontinue to run. However, when itreaches a stage that requires thelid to be closed, the error will occur.Closing the lid should dismissthe error and resume normaloperation. |
| Ld | Too Long to Drain Water. The washer has detectedthat it is taking too longto completely drain waterfrom the wash tub. Check to make sure the drain hoseis properly installed. The open endof the drain hose should not besubmerged in water. |
| UL | Unbalanced load. The washer has detectedan out of balance load andhas failed to self correctthe condition. Open the washer lid, redistributethe load, close the lid, and thewasher will resume operation. |
| Lf | Too long to fill. The washer senses that itis taking too long to fill thewash tub or does not reada change in water levelduring a fill. Check to make sure that thewater hoses are connected to thewasher, there are no kinks in thehoses, and that the supply valvesare fully opened. |
| f2 | Water Level is Too High. The washer has detected higher than normal waterlevels, automatic draininghas not resolved the issue. |
| E1 | Washer cannot drain the water within 4 minutes. Clear the pump. Service is required. |
| E2 | Cannot lock the door after 20 seconds. Service is required. |
| E4 | After 8 min, the selected water level has not been reached. Check plumbing and water hose connections. Service is required. |
| E5 | Water Temperature Problem. The washer senses thatHot water is too cold, orWarm, Cool, Cold, and TapCold water is too hot. Check to make sure that yourhot water heater is supplying hotwater. Check to make sure that the water hoses are connected to the proper valve; hot to hot, cold to cold. |
| E8 | Water level above the warning level. |
| E10 | Service is required. |
| E13 | Caused by buildup of lint. |
| FA | Water level sensor circuit problem. |
| FC | No feedback signal from driver unit. |
| Fd | Dryer heating is abnormal. |
| FE | Dryer motor is abnormal. |
Parts Meaning
Power-off memory function: In case of abrupt power failure or the need to cut off the power during a program cycle, the present settings will be saved and the preset operation will resume when the power is on again.
Note: During the spin process, if too much foam is inspected, in order to protect the motor, the washing machine will eliminate the foam automatically; the motor will stop and the drain pump will drain the water continuously for 90 seconds. If it happens more than 3 times, the motor will stop until the end of cycle without spinning.
Control Panel Buttons Meaning
Troubleshooting
The following circumstances do not mean there is a fault with the appliance. Contact the Customer Care Team when you have confirmed the problem after following the instructions below.
Cleaning and Care
Cleaning the filter
Caution: Place a container under the drain pump filter, to collect any excess water that may come out of the drain pump when the filter is removed.
Clean the filter once a month:
- Open the bottom cover (Fig. 2).
- Remove the filter by turning counterclockwise (Fig. 2b).
- Flush the filter clean with running water (Fig. 2c).
- Replace the filter by turning clockwise and remount the cover (Fig. 2d).
Dryer Codes
| Error Codes | Solutions |
|---|---|
| C9 | Short Circuit. The PCBs failed. |
| E4 | Heating Element Problem. The humidity sensor failed. The unit will complete thecurrent operating cycle. The unit can still operate under the Time cycles. |
| E5 | The temperature sensor failed. |
| E1 | The door is notclosed tightly. Shut the door tightly and restartthe machine. |
| E2 | There is no changein the temperatures of the laundry inthe tub. |
| E3 | The laundry is not dried. |
| E5 | The thermal sensoropen-circuited or short circuited. |
| E6 | Drain pump fails. |
| E7 | Under voltage or over voltage fault. Check the voltage of power supply. |
| E8 | Over load warning. Check the voltage of power supply. Reduce the load and restart the programme. |
| F2 | Drain pump error. |
| F4 | 1,Temperature of the laundry in the drum does not change. 2,Refrigerant leaks. |
| F32 | The condenser thermal sensor is open-circuited or short-circuited. |
| F33 | The condenser thermal sensor is open-circuited or short-circuited. |
| F5 | Communication failure between PCB and display. |
| cln LInt | The filters is clogged. Clean both filters. |
| H2O FULL | The water tank is full. Clean the water tank. |
| Lo | Ambient temperature is too low. Only use the dryer at ambient temperatures higher than 5 °C. |
Dryer Control Panel
Dryer Troubleshooting
In case of power failure, the current programme is stored only for a short time. Usually, a restart of the program is required.
| Trouble | Possible Solution |
|---|---|
| Appliance fails to operate and the display shows 'End' | Check the program setting and post-dry if necessary. Check the drum. |
| Drying time is too long. | Clean the condenser filter. Reduce the amount of laundry. Spin the laundry properly before drying. Pay attention to the installation instructions. and increase the ambient temperature, if possible. |
| Drying time is too short. | For single items or small amount of laundry the TIME programme should be selected. Select the TIME programme or a higher dry level. |
| Creasing at the laundry. | Reduce the amount of laundry. Remove laundry immediately after programme end, hang them up and pull them into shape. Select and adjust the programme according to the fabric type. |
| Door does not close. | Insert laundry correctly. |
| Remaining time on the display stops or skips. | The automatic adjustment is a normal operation. |
| The drum interior light does not work. | Check power supply. Switch the machine on. |
| Strong rumbling noise | The dryer rack is not properly installed. Correct the seat of the dryer rack. |
Manual Pdf
Haier Automatic Front Loading Washing Machine Manual PDF
Haier Heat Pump Dryer User Manual PDF
- Samsung Refrigerator Error Codes List - March 10, 2025
- KitchenAid Oven Error Codes and Troubleshooting - March 10, 2025
- iLife Robot Vacuum Error Codes and Troubleshooting - March 10, 2025
in lock can not open the door
FA light on the machina
Water level sensor circuit problem.
It came up clean filter during a cycle, I need a fancier dish as even a take away dish was too deep to fit under the filter, anyway I am about 300 towels in and still water draining out.
Door refuses to open for a week now, keeps saying E1 even after ensuring it’s properly locked, I’ve restarted the machine over and over, at the end of every cycle it says E1 and refuses to open, what can I do please.
What does fc2 mean how do U fix it
Did you figure bit out? Mines just started saying this to